Cattle Crush Specialist Range

Dairymaster Cattle Crush

DAIRYMASTER-COW-ONLY-502x350

Dairymaster Cattle Crush

Yoke Description:
  • Rope operated yoke incorporated into the front exit gate and used from the rear.
  • Adjustable neck yoke with four settings from 145mm to 230mm.
  • Baffle plates eliminate potential leg traps.
Body Description:
  • Front side gates hinge from the front pillar.
  • Bolted construction timber floor.
  • Rear drop down floor extensions to help prevent the cow from rocking the crush with rear feet.
  • Two adjustable front foot blocks.
  • Geared winch to raise / lower feet.
  • Adjustable belly band.
  • Adjustable rump chain.
Optional Extra for Dairymaster Cattle Crush
  • 3 rail side gates c/w chains to close gap at rear open side section
  • Can be chained to race section
  • Pair of 1830mm long 3 rail gates.

Highland Cattle Crush

IMG_9067-525x350

Highland Cattle Crush

Designed specifically for the Highland cattle breed. The sides of this unit are only 1100mm high which allows the horns to pass safely over the top.

  • Manually operated scissor yoke with fully retractable yoke arms.Lever operating handle lifts the yoke upwards after the animals head has gone past.
  • Simple quiet winding adjustment gives infinite yoke widths between 100mm and 290mm.
  • Two piece wrap around front gates open out in a single operation to allow full unobstructed access to the animals head.
  • Two short side doors on each side hinge from a middle pillar to allow access to the animal's flanks.
  • Traditional backing up bar facility built into the side gates, rear gate included as standard.
  • Pallet fork lifting points welded onto the top horizontal rails.
  • One removable extension rail on each side sit above the side gates to allow full access to the animal's flanks.
  • Fully welded slightly tapered tread plate floor to help keep the animals feet inside the crush when the side doors are open.
  • Length 2775mm : Base Length 2170mm : Width 1300mm : Internal Width 738mm : Height 1900mm

Champion Beef Master Cattle Crush

CHAMPION-BEEFMASTER3-502x350

Champion Beef Master Cattle Crush

This crush is designed specifically for larger breeds and is an extremely heavy duty unit.

  • Manual traditional lever operated yoke handle can be used on either side. Spring loaded quick release adjustment gives 4 preset yoke widths from 165mm to 330mm.
  • Fully opening front and side gates form the front cage enabling greater access all around the animals head.
  • Fully welded tread plate floor to help keep the animals feet inside the crush when the side doors are open.
  • Two full height side doors on each side, hinged from a middle pillar, allow full access with no obstructions to the animal's flanks.
  • Rear gate included as standard.
  • Traditional backing up bar facility built into the side gates.
  • Pallet fork lifting points welded onto the top horizontal rails.
  • Length 3120mm : Base Length 3000mm : Width 1000mm : Internal Width 900mm : Height 1950mm

Professional Cattle Crush

IMG_0306-525x350

A1000 Cattle Crush

The new A1000 cattle crush is supremely robust. It has been designed for use in professional environments where cattle are frequently handled in high numbers. If strength, ease of use and longevity are priorities when choosing your cattle crush, the A1000 will easily meet your needs.
The A1000 yoke is the ultimate evolution of the Saracen yoke concept. Highly developed and with an upgraded specification, the stronger and heavier yoke can be set with 7 different apertures from 100 to 260mm, and is easily adjusted. The yokes are set using the rotating handle and locking bar, and readjusted in one easy movement. The telescopic adjustment features sliding bearings to keep vibration and noise to an absolute minimum.
The two leaves of the yoke are fully synchronized and operate as a cohesive unit which curtail pressure when animals approach the yoke at an oblique angle. Fully sheeted internally, the yokes are designed with paramount animal safety in mind.

  • Internal dimension of 760mm to allow large animals to fit in the crush with ease.
  • Three full length side gates on each side to offer full access to the whole of the animal when fully opened. These can be opened in stages to keep the animal contained at all times, increasing operator safety.
  • Advanced polyethylene bushed hinges and polymer/steel easy to open latches to reduce crush noise signature and enhance overall feel of the product.
  • Integrated load bar points.

IMG_0529-525x350

M1000

The new M1000 yoke represents the pinnacle of manual yoke design and encompasses the foremost yoke concepts. Speed is a key feature of the M1000. A sliding gate design, the yoke is positioned manually using the smooth action operating handle. At whatever point the yokes are positioned, they lock automatically, rendering the intensive individual adjustment unnecessary. The doors are then easily unlocked and opened by the operating handle in one easy movement.
The super quiet, ratchet free design is an advantage when handling nervous cattle. The yoke also entices animals into and through the crush by being left fully open by the operator, yet is quick enough to catch the animal as it passes, this saves time and manpower. The yoke will lock at any point throughout its range of movement, this highly adjustable design makes the M1000 yoke ideal for mixed herds, as well as short horned cattle. The solid front gates of the M1000 mean zero leg traps at all points of the yoke's operation.

  • Internal dimension of 760mm to allow large animals to fit in the crush with ease.
  • Three full length side gates on each side to offer full access to the whole of the animal when fully opened. These can be opened in stages to keep the animal contained at all times, increasing operator safety.
  • Advanced polyethylene bushed hinges and polymer / steel easy open latches to reduce crush noise signature and enhance overall feel of the product.
  • Integrated load bar points.