Philmac Water Fittings

The revolutionary Philmac Water Fittings Metric/Imperial Pipe Fitting range.

MDPE and Imperial Polythene Installation Instructions.

philmac-water-fittings

1. Cut the pipe square.
There is no need to prepare the pipe end. Chamfering or lubrication is not required.

philmac-water-fittings

2. Insert liner in MDPE pipe.
With MDPE pipe a liner must be used to ensure conformance with WRAS.

philmac-water-fittings

3. No liner or insert required for imperial pipe.
For connections to imperial PE pipe (BS1972/3284 and IRS 135 Heavy Gauge) a liner or insert is not required.

philmac-water-fittings

4. Ready to use position.
The fitting is pre-assembled and ready to use. Always ensure the nut is fully relaxed and 2 threads are showing before inserting the pipe.

philmac-water-fittings

5.Pipe insertion.
Slide the pipe fully into the fitting to the point where the stop is felt.

philmac-water-fittings

6. Nut Tightening.
Tighten the nut by hand and then firmly with a wrench if required.

philmac-water-fittings

7. Fully installed.
Fitting is now fully installed.

philmac-water-fittings

8. Imperial fully installed.
For connections to Imperial PE pipe (BS1972/3284 and IRS 135 Heavy Gauge) steps 5 and 6 are the same as for MDPE connections.

philmac-water-fittings

9. Disassembly
To disassemble the fitting simply loosen the nut until 2 threads are showing. Pipe will be released and can simply be pulled out of the fitting.

Reducing and Copper connection Philmac Water Fittings Kits Installation Instructions.

philmac-water-fitting

1. Preparation.
Take the Metric/Imperial fitting and remove the nut. The split collet and seal ring must then be removed.

philmac-water-fittings

2. Position the connection kit.
Take the appropriate connection kit and place it in the body of the fitting with the tapered end pointing outwards.

philmac-water-fittings

3. Ready to use.
Replace the nut on the fitting body. The fitting is now ready for use. Standard installation instructions now apply.

Copper Philmac Water Fittings Installation Instructions

Repeat steps 1 to 3 above using the Philmac Water Fittings copper connection kit.

philmac-water-fittings

1.Cut the pipe square.
Pipe should be deburred, degreased and roughened with wire wool or similar.

philmac-water-fittings

2. Ready to use position.
Prior to pipe insertion ensure the nut is fully relaxed and 2 threads are showing.

philmac-water-fittings

3. Witness mark the pipe.
To ensure the correct insertion depth witness the mark by lining up the pipe against the fitting and using the flange of the body as an indicator.

philmac-water-fittings

4. Pipe Insertion.
Slide the pipe fully into the fitting up to the witness mark.

philmac-water-fittings

5. Nut tightening.
Tighten the nut by hand and then firmly with a wrench if required.

philmac-water-fittings

6. Fully installed.
The fitting is fully installed when the nut butts against the flange of the body.

philmac-water-fittings

Metric/Imperial Joiner

20mm 1/2"
25mm 3/4"
32mm 1"
40mm 1 1/4"
50mm 1 1/2"
63mm 2"

philmac-water-fittings

Metric / Imperial Elbow

20mm 1/2"
25mm 3/4"
32mm 1"
40mm 1 1/4"
50mm 1 1/2"
63mm 2"
25mm x 20mm 3/4" x 1/2"

philmac-water-fittings

Metric/Imperial TEE - Equal

20mm 1/2"
25mm 3/4"
32mm 1"
40mm 1 1/4"
50mm 1 1/2"
63mm 2"

philmac-water-fittings

Metric/Imperial Reducing Sets

25mmx 20mm 3/4" x 1/2"
32mm x 20mm 1" x 1/2"
32mm x 25mm 1" x 3/4"
50mm x 25mm 1 1/2" x 3/4"
50mm x 32mm 1 1/2" x 1"
63mm x 25mm 2" x 3/4"
63mm x 32mm 2" x 1"
63mm x 50mm 2" x 1 1/2"

philmac-water-fitting

Metric/Imperial Wall Plate Elbow Plastic

20mm 1/2"
25mm 3/4"

philmac-water-fittings

Metric/Imperial Reducing Joiner

25mmx 20mm 3/4" x 1/2"
32mm x 20mm 1" x 1/2"
32mm x 25mm 1" x 3/4"
50mm x 25mm 1 1/2" x 3/4"
50mm x 32mm 1 1/2" x 1"
63mm x 25mm 2" x 3/4"
63mm x 32mm 2" x 1"
63mm x 50mm 2" x 1 1/2"

philmac-water-fittings

Metric/Imperial TEE - Equal

20mm 1/2"
25mm 3/4"
32mm 1"
40mm 1 1/4"
50mm 1 1/2"
63mm 2"

philmac-water-fittings

Bush Reducing

25mmx 20mm 3/4" x 1/2"
32mm x 20mm 1" x 1/2"
32mm x 25mm 1" x 3/4"
50mm x 25mm 1 1/2" x 3/4"
50mm x 32mm 1 1/2" x 1"
63mm x 25mm 2" x 3/4"
63mm x 32mm 2" x 1"
63mm x 50mm 2" x 1 1/2"

philmac-water-fittings

 

Cap

20mm 1/2"
25mm 3/4"
32mm 1"
40mm 1 1/4"
50mm 1 1/2"
63mm 2"

philmac-water-fittings

Socket

20mm 1/2"
25mm 3/4"
32mm 1"
40mm 1 1/4"
50mm 1 1/2"
63mm 2"

philmac-water-fittings

Crutch Head Stop cock

20mm 1/2"
25mm 3/4"
32mm 1"

philmac-water-fittings

Tee Joint Female Center

philmac-water-fittings

Metric/Imperial End Cap

20mm 1/2"
25mm 3/4"
32mm 1"
40mm 1 1/4"
50mm 1 1/2"
63mm 2"

philmac-water-fittings

Female Elbow

philmac-water-fittings

End Connector Male

philmac-water-fittings

End Connector Female

philmac-water-fittings

Ball Valve

25mm 3/4"
32mm 1"
40mm 1 1/4"
50mm 1 1/2"
63mm 2"

philmac-water-fittings

Pipe Support Liner

20mm 1/2"
25mm 3/4"

[sc:SalesTexts ]