BRITES Sales Hotline 01239 891618 / 891376

Home
Cattle Crushes 1
Cattle Crushes 2
Cattle Crush 3
Squeeze Crush
Weighing Systems
Cattle Handling
Cattle Handling
Cattle Feeding
Cattle Feeding
Cow Cubicles
Dairy Wash Troughs
Calf Equipment
Sheep Equipment
Sheep Feeding
Sheep Handling
Bull Equipment
Foot Baths
Gates Galvanised
Galebreaker
Silage Sheets
Vacuum Film
Silaflex
Wooden Gates
Gate Furniture
Cattle Grids
Water
Philmac Water Fittings
Water Troughs
Galv Water Trough
Storage Tanks
Dog Run / Penning
Contract Fencing
Electric Fencing
Feed Troughs /Plastic
Equestrian
PERMAPOST FENCING
Steel Fencing
Raised Beds
Mowers Etc
New Page 19
Agri Fab
Muck Boot
Coal & Logs
Contact Details
About Us
What Our Customers Say
Photo Gallery
News
Terms & Conditions
The revolutionary Philmac Metric/Imperial Pipe Fitting range.
 

MDPE and Imperial Polythene Installation Instructions.

1. Cut the pipe square.
There is no need to prepare the pipe end. Chamfering or lubrication is not required.		 2. Insert liner in MDPE pipe.
With MDPE pipe a liner must be used to ensure conformance with WRAS.		 3. No liner or insert required for imperial pipe.
For connections to imperial PE pipe (BS1972/3284 and IRS 135 Heavy Gauge) a liner or insert is not required.

4. Ready to use position.
The fitting is pre-assembled and ready to use. Always ensure the nut is fully relaxed and 2 threads are showing before inserting the pipe.		 5.Pipe insertion.
Slide the pipe fully into the fitting to the point where the stop is felt.		 6. Nut Tightening.
Tighten the nut by hand and then firmly with a wrench if required.

7. Fully installed.
Fitting is now fully installed.		 8. Imperial fully installed.
For connections to Imperial PE pipe (BS1972/3284 and IRS 135 Heavy Gauge) steps 5 and 6 are the same as for MDPE connections.		 9. Disassembly
To disassemble the fitting simply loosen the nut until 2 threads are showing. Pipe will be released and can simply be pulled out of the fitting.
     

Reducing and Copper connection Kits Installation Instructions.

1. Preparation.
Take the Metric/Imperial fitting and remove the nut. The split collet and seal ring must then be removed.		 2. Position the connection kit.
Take the appropriate connection kit and place it in the body of the fitting with the tapered end pointing outwards.		 3. Ready to use.
Replace the nut on the fitting body. The fitting is now ready for use. Standard installation instructions now apply.
     

Copper Installation Instructions
Repeat steps 1 to 3 above using the copper connection kit.

1.Cut the pipe square.
Pipe should be deburred, degreased and roughened with wire wool or similar.		 2. Ready to use position.
Prior to pipe insertion ensure the nut is fully relaxed and 2 threads are showing.		 3. Witness mark the pipe.
To ensure the correct insertion depth witness the mark by lining up the pipe against the fitting and using the flange of the body as an indicator.

4. Pipe Insertion.
Slide the pipe fully into the fitting up to the witness mark.		 5. Nut tightening.
Tighten the nut by hand and then firmly with a wrench if required.		 6. Fully installed.
The fitting is fully installed when the nut butts against the flange of the body.

 

    
 
 
 
3G Joiner/Coupler

Metric/Imperial Joiner

20mm 1/2"
25mm 3/4"
32mm 1"
40mm 1 1/4"
50mm 1 1/2"
63mm 2"

3G Elbow

Metric/Imperial Elbow

20mm 1/2"
25mm 3/4"
32mm 1"
40mm 1 1/4"
50mm 1 1/2"
63mm 2"
25mm x 20mm 3/4" x 1/2"
       
3G Tee

Metric/Imperial TEE - Equal

20mm 1/2"
25mm 3/4"
32mm 1"
40mm 1 1/4"
50mm 1 1/2"
63mm 2"

3G Metric/Imperial Reducing Kit (L)

Metric/Imperial Reducing Sets.

25mmx 20mm 3/4" x 1/2"
32mm x 20mm 1" x 1/2"
32mm x 25mm 1" x 3/4"
50mm x 25mm 1 1/2" x 3/4"
50mm x 32mm 1 1/2" x 1"
63mm x 25mm 2" x 3/4"
63mm x 32mm 2" x 1"
63mm x 50mm 2" x 1 1/2"
       
3g Wall Plate Elbow Metric/Imperial Wall Plate Elbow Plastic
 
20mm 1/2"
25mm 3/4"


 

 mim-red

Metric/Imperial Reducing Joiner

25mmx 20mm 3/4" x 1/2"
32mm x 20mm 1" x 1/2"
32mm x 25mm 1" x 3/4"
50mm x 25mm 1 1/2" x 3/4"
50mm x 32mm 1 1/2" x 1"
63mm x 25mm 2" x 3/4"
63mm x 32mm 2" x 1"
63mm x 50mm 2" x 1 1/2"
       

90426600

 Metric/Imperial TEE - Equal
 
20mm 1/2"
25mm 3/4"
32mm 1"
40mm 1 1/4"
50mm 1 1/2"
63mm 2"
90412100 BSP Bush Bush Reducing
25mmx 20mm 3/4" x 1/2"
32mm x 20mm 1" x 1/2"
32mm x 25mm 1" x 3/4"
50mm x 25mm 1 1/2" x 3/4"
50mm x 32mm 1 1/2" x 1"
63mm x 25mm 2" x 3/4"
63mm x 32mm 2" x 1"
63mm x 50mm 2" x 1 1/2"
       
90401100 BSP Plug

Cap

20mm 1/2"
25mm 3/4"
32mm 1"
40mm 1 1/4"
50mm 1 1/2"
63mm 2"
90436600-99

Socket

20mm 1/2"
25mm 3/4"
32mm 1"
40mm 1 1/4"
50mm 1 1/2"
63mm 2"
 
       

gunmetal stopcock UK

Crutch Head Stop Cock

20mm 1/2"
25mm 3/4"
32mm 1"

 

 3G FI Tee

Tee Joint Female center
       
3G End Cap

Metric/Imperial End Cap

20mm 1/2"
25mm 3/4"
32mm 1"
40mm 1 1/4"
50mm 1 1/2"
63mm 2"
3G FI Elbow

Female Elbow
       

3G FI End Connector /Female Adaptor

End Connector male

 3G MI End Connector/Male Adaptor

End Connector Female
       

95500400

 Ball Valve
 
25mm 3/4"
32mm 1"
40mm 1 1/4"
50mm 1 1/2"
63mm 2"
pipe liner Pipe Support Liner
 
20mm 1/2"
25mm 3/4"
32mm 1"
40mm 1 1/4"
50mm 1 1/2"
63mm 2"
       
Pipe Cutter UK Pipe Cutter
Up to 32mm medium.
Up to 63mm Large.		 Pipe clip cobra Cobra Pipe Clips
 
20mm 1/2"
25mm 3/4"
32mm 1"
40mm 1 1/4"
50mm 1 1/2"
63mm 2"
       

Stopcock

20mm 1/2"
25mm 3/4"
32mm 1"

Philmac Metric/Imperila Blank Plug

Blanking Plug
       

Philmac Tank Connector

Tank Connector

25mm 3/4"
32mm 1"

 

    
       
       

Huge range of Philmac Water Fittings always
IN STOCK!
Ring 01239 891618 / 01239 891376
e.mail: sales@country-stores.com