Sheep Hurdles

We offer a wide variety of sheep hurdles, from standard interlocking also the pin type and heavy duty range of Sheep Hurdles. We carry a large range of IAE Sheep Hurdles in stock.

7 Rail Interlocking Sheep Hurdle

The 7 rail interlocking sheep hurdle has a loop type coupling arrangement, 970mm high, sizes: 3ft, 4ft in stock, 5ft, 6ft in stock, and 8ft in stock long.

Note: The intended use for interlocking sheep hurdles is to form large holding pens or small individual pens. If used for long single runs of lambing pens or back to back lambing pens some joints will need to be cable tied together.

Part Meshed Lambing Hurdle

The part meshed lamb hurdle can be used to form banks of single runs, or back to back runs of lambing pens due to top loose ring and fixed 60mm x 60mm bottom lug type coupling arrangement.Not compatible with standard 7 rail interlocking sheep hurdles

1050mm high with 5 horizontal rails and clad with 50mm x 50mm weldmesh up to height of 524mm from finished floor level. Available sizes: 4ft in stock and 6ft in stock

 

Lamb Creep Hurdle

This lamb creep hurdle is a loop type arrangement to ensure compatibility with interlocking sheep hurdles, 1830mm long x 970mm high with 7 horizontal rails. Creep apertures built in to a 535mm approx long opening at one end.

Alpaca Hurdle

Loop type coupling arrangement, 1296mm high. Available size 6ft and 8ft long

6 Railed Sheep Hurdles

IAE 6 Railed Sheep Hurdles c/w drilled lugs at each end. 1000mm high

Sizes available:

  • 2ft 2″ In Stock
  • 4ft 1” In Stock
  • 5ft Ring for availability
  • 5ft 10″
  • 8ft 2” In Stock
  • 10ft Ring for availability

4 Railed Sheeted Sheep Hurdles

IAE 4 Rail Fully Sheeted Sheep Hurdles c/w drilled lugs at each end. 1000mm high.

Sizes:

  • 660mm (2ft 1/2″) In Stock
  • 915mm (3ft)
  • 1250mm (4ft 1″)
  • 1525mm (5ft)
  • 1730mm (5ft 8″)
  • 2500mm (8ft 2″) In Stock
  • 3050mm (10ft) In Stock

6 Railed Sheep Sliding Gate Hurdles

IAE 6 Rail Sheep sliding gate hurdles c/w drilled lugs at each end

  • 1000mm high
  • Opening of slide section is 1205mm wide
  • Opening section has no top rail to navigate under

Sizes available:

  • 6 rail 2500mm (8ft 2″) In Stock
  • 6 rail 2820mm (9ft 3″)
  • 6 rail 3050mm (10ft)

6 Railed Sheep Hurdles Gate One End

IAE 6 Rail Sheep Hurdle c/w Hinged Gate Built Into One End and Drilled Lugs at both ends.

  • 1000mm high
  • Opening of gate section is 835mm wide
  • Gate has a top operated spring loaded slide bolt.
  • 6 rail 2500mm (8ft 2″) Long
  • In Stock

Pair of 6 Rail Sheep Gates in Frame

Built into a frame c/w Drilled Lugs at each end.

  • 1000mm High
  • Gates are joined in the middle with a drop over frame
  • 6 Rail
  • Length 2500mm (8ft 2″)
  • In stock

Radiused Hurdle

A Radiused Hurdle that is available either railed or sheeted and in a variety of lengths to suit all needs and requirements.

Dimensions:

  • 1000mm high

Sizes:

  • 6ft 6”Railed
  • 6ft 6” Sheeted
  • 3ft 7”Sheeted
  • 5ft 6”Sheeted
  • 6ft 1”Sheeted

Sheep Swing Gates Built into a Frame

IAE Sheep swinging gate built into a frame c/w drilled lugs at each end

  • 1000mm High.
  • Gate has a top operated spring loaded slide bolt

Sizes Available:

  • 6 rail 660mm (2ft)
  • 6 rail 915mm (3ft) In stock
  • 6 rail 1250mm (4ft 1″) In stock
  • 6 rail 1525mm (5ft) In Stock
  • Sheeted 1525mm (5ft)

Fully Sheeted Sheep Shedding Hurdle

  • This Fully Sheeted Sheep Shedding Hurdle is 1000mm High.
  • Gate has a top operated lever to divert animals into an adjacent pen.
  • Gate section can be hinged from either end to make units handed.
  • Note: gate on 8ft 2″ is central hinged.
  • Sizes available: 5ft and 8ft 2″ long
  • 8ft 2″ long In Stock

Non Return Gate in Race Joining Frame

The Non Return Gate in Race Joining Frame base is drilled so that adjoining race hurdles can be tapered if required when working with lambs

Clip On Non Return Gate

Clip on Non return Gate In Stock

This Clip on Non Return Gate attaches to sheeted race hurdles.

Race Joining Frame

The Race Joining Frame base is drilled so that adjoining race hurdles can be tapered if required when working with lambs.

Drop Gate In Race Joining Frame

This Drop Gate In Race Joining Frame base is drilled so that adjoining race hurdles can be tapered if required when working with lambs.

Fully Sheeted “Slipway” Sheep Hurdle

  • Used when animals are to be put into a dipping bath. (dipping bath not included).
  • Lift out section has inverted hooks at each end
  • Lift out hurdle can be replaced by a curtain (extra cost).
  • Open section is 1500mm approx wide in both available options.
  • Options available: 5ft with removable panel, 10ft with removable panel.

Swing and Slide Gate

The swing and slide gate is a tried and tested unique gate with a curved top rail at each end to allow the gate to travel through a pivot wheel and behind the next batch of animals. Enables sheep to be both sides of the gate without obstruction which in turn means full pens all of the time, a slide bolt is built into the gate at each end. Options: 8ft 3″ gate only , 5ft 6″ gate in frame, 76mm Hanging post to suit swing and slide gate c/w pivot.

Fully Meshed Drafting Stop Gate

Fully Meshed Drafting Stop Gate Used to divert animals from race into two pens. The longer operating handle means that the operator can be out of the animals sight which encourages the sheep to keep moving forward. A drop over latch will lock gate in the “stop” position. Base is drilled so that adjoining race hurdles can be tapered if required when working on lambs. Size: 570mm wide x 980mm long

Dimensions:

  • 1000mm high x 570mm wide x 980mm long

Three Way Drafting/Stop Gate

The three way drafting gate is a facility to allow the stock to travel straight through the race or to be diverted to the right or left. Meshed stop gate is hinged and connected to one diverter gate. Floor plates at both ends allow for the race to be tapered if required. Size: 570mm wide x 980mm long.

Standard Guillotine Gate

The standard guillotine gate is used to allow man access through gate if required but enables the gate to be lifted when moving sheep. Bases are drilled so that adjoining race hurdles can be tapered if required when working on lambs. Unit has full height vertical guide tube on one side (allows gate to swing & lift) & guide plates opposite (up to 1000mm high) Size available: 570mm wide.

Sheep Non Return/Stop Gate in Frame

IAE Sheep non return / stop gate in frame c/w drilled lugs at each end.

  • Base is drilled so that adjoining race hurdles can be tapered if required when working on lambs.
  • Gate can be locked open, locked closed (stop gate) and used as a traditional non return gate.
  • 570mm wide x 270mm deep
  • In Stock

Sheep Self Locking Yoke Gate in Race Frame IAE

IAE Sheep Self Locking Yoke Gate in Race Frame c/w drilled lugs at each end.

  • Base is drilled so that adjoining race hurdles can be tapered if required when working with lambs.
  • Yoke has 5 settings varying in width between 5mm and 130mm
  • Yoke gates can be locked open when not in use.
  • In Stock

Sheep Dual Gates in Race Frame

The base of the Sheep Dual Gates in Race Frame is drilled so that adjoining race hurdles can be tapered if required when working on lambs. Quick acting stop gates concertina out of the way.

6 Rail Gate in Race Joining Frame

Base drilled so that adjoining race hurdles can be tapered if required when working with lambs. Size: 570mm wide

Sheep Sliding/Stop Gate in Race Frame

Sheep sliding / stop gate in race frame c/w drilled lugs at each end

  • Base is drilled so that adjoining race hurdles can be tapered if required when working on lambs.
  • Meshed gate slides positively in and out of position using a scissor action.
  • 570mm wide.
  • In Stock

Lift & Swing Guillotine Gates

Lift & Swing Guillotine Gate

Used to allow man access through gate if required but enables the gate to be lifted when moving sheep. Bases are drilled so that adjoining race hurdles can be tapered if required when working on lambs. Unit has full height vertical guide tube on one side (allows gate to swing & lift) & guide plates opposite (up to 1000mm high) Size available: 570mm wide.

Lift & Swing Guillotine Gate c/w pivot to suit swing & slide gate

Main frame is full height both sides but includes pivot and fittings to accommodate swing and slide gate only if required. Bases are drilled so that adjoining race hurdles can be tapered if required when working on lambs, pulley and nylon rope is included. Size: 570mm wide

 

Can't find a product? Got a Question?

We provide a dedicated service, we answer when you call and give you the information you need, no answer phone options, straight to someone who can deal with your enquiry promptly. We are also competitively priced and are ready and waiting to take your calls 7 days a week.